reklama

Stav SSD pomocí smartctl

Petr

Stav SSD pomocí smartctl
« kdy: 30. 11. 2018, 21:29:03 »
Blbne mě disk ale nedokážu se orientovat ve výpisu smartctl, poradil by mě někdo jestli umírá nebo ne?


Kód: [Vybrat]
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     ADATA SU700
Serial Number:    2H2320062333
LU WWN Device Id: 5 707c18 10050c4d5
Firmware Version: B170428a
User Capacity:    240,057,409,536 bytes [240 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Nov 30 20:49:21 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (   33) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: (   1) minutes.
Extended self-test routine
recommended polling time: (   1) minutes.
Conveyance self-test routine
recommended polling time: (   1) minutes.
SCT capabilities:        (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       763
 12 Power_Cycle_Count       0x0012   100   100   000    Old_age   Always       -       242
167 Unknown_Attribute       0x0022   100   100   000    Old_age   Always       -       0
168 Unknown_Attribute       0x0012   100   100   000    Old_age   Always       -       4
169 Unknown_Attribute       0x0013   093   093   010    Pre-fail  Always       -       257701970367
173 Unknown_Attribute       0x0012   200   200   000    Old_age   Always       -       30066540559
175 Program_Fail_Count_Chip 0x0013   040   100   010    Pre-fail  Always       -       0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033   093   093   020    Pre-fail  Always       -       852
192 Power-Off_Retract_Count 0x0012   100   100   000    Old_age   Always       -       31
194 Temperature_Celsius     0x0022   066   066   030    Old_age   Always       -       34 (Min/Max 33/40)
231 Temperature_Celsius     0x0033   094   094   005    Pre-fail  Always       -       1536
233 Media_Wearout_Indicator 0x0032   100   100   000    Old_age   Always       -       3387088512
234 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       1606804930560
241 Total_LBAs_Written      0x0032   100   100   000    Old_age   Always       -       2724954965
242 Total_LBAs_Read         0x0032   100   100   000    Old_age   Always       -       3829255297

SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:42:32.800  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:42:27.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:42:27.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:42:27.500  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:42:27.500  SET FEATURES [Enable SATA feature]

Error 9 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:41:49.300  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:41:43.900  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:41:43.900  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:41:43.900  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:41:43.900  SET FEATURES [Enable SATA feature]

Error 8 occurred at disk power-on lifetime: 759 hours (31 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:04:34.500  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:04:29.200  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:04:29.200  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:04:29.200  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:04:29.200  SET FEATURES [Enable SATA feature]

Error 7 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 80 f9 a0 e1  Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 80 f9 a0 e1 08      00:05:28.500  READ DMA
  ca 00 28 18 df a1 e1 08      00:05:28.500  WRITE DMA
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:05:28.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:05:28.500  SET FEATURES [Set transfer mode]

Error 6 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 80 f9 a0 e1  Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 80 f9 a0 e1 08      00:05:28.500  READ DMA
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:05:28.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:05:28.500  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       763         -
# 2  Extended offline    Completed without error       00%       763         -
# 3  Extended offline    Completed without error       00%       760         -
# 4  Short offline       Completed without error       00%       759         -
# 5  Short offline       Completed without error       00%       754         -
# 6  Short offline       Completed without error       00%       412         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
« Poslední změna: 30. 11. 2018, 22:32:55 od Petr Krčmář »

reklama


Kylo

Re:SSD disk
« Odpověď #1 kdy: 30. 11. 2018, 21:50:51 »
Smart na SSD ? To jako proc ?

Lol Phirae

Re:SSD disk
« Odpověď #2 kdy: 30. 11. 2018, 22:17:06 »
Smart na SSD ? To jako proc ?

Překvapivě některý lidi rádi monitorujou disky a objednaj si nový, než jim ten stávající chcípne.  ::)

Re:Stav SSD pomocí smartctl
« Odpověď #3 kdy: 30. 11. 2018, 23:02:06 »
Mám velmi špatné zkušenosti se SMART hodnotama z různých SSD, často jsou nelogické. Řadiče nebo SW očekávají zcela odlišné hodnoty a pak drze hlásí "stav 100%" a disk je v háji.
Tak se řídím jen hodnotou kolik je zapsáno dat a typem disku (MLC, TLC).

Tenhle má zapsáno asi 1.27 TB což je hodně málo. Ty chyby co píše mi příjdou spíš jako kdyby od něj nějaký SW chtěl cosi nestandardního.
« Poslední změna: 30. 11. 2018, 23:07:08 od Jan Forman »
„Řemeslo se naučí každý. Umění nikdo.“
„Jednoduchost je nejvyšší úroveň sofistikovanosti.“
- Leonardo Da Vinci

trubicoid2

Re:Stav SSD pomocí smartctl
« Odpověď #4 kdy: 30. 11. 2018, 23:36:58 »
přijde mi to jako vadnej kabel? nebo řadič?


Kylo

Re:SSD disk
« Odpověď #5 kdy: 30. 11. 2018, 23:46:48 »
Smart na SSD ? To jako proc ?

Překvapivě některý lidi rádi monitorujou disky a objednaj si nový, než jim ten stávající chcípne.  ::)

Bejvavalo v minulem tisicileti. Dneska jsou SSD naletovany na zakladovce.

Lol Phirae

Re:SSD disk
« Odpověď #6 kdy: 30. 11. 2018, 23:52:07 »
Bejvavalo v minulem tisicileti. Dneska jsou SSD naletovany na zakladovce.

Že si kupuješ naletovaný kokotiny, to je tvůj problém.

 

reklama