Fórum Root.cz

Hlavní témata => Hardware => Téma založeno: Petr 30. 11. 2018, 21:29:03

Název: Stav SSD pomocí smartctl
Přispěvatel: Petr 30. 11. 2018, 21:29:03
Blbne mě disk ale nedokážu se orientovat ve výpisu smartctl, poradil by mě někdo jestli umírá nebo ne?


Kód: [Vybrat]
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     ADATA SU700
Serial Number:    2H2320062333
LU WWN Device Id: 5 707c18 10050c4d5
Firmware Version: B170428a
User Capacity:    240,057,409,536 bytes [240 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2 (minor revision not indicated)
SATA Version is:  SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Fri Nov 30 20:49:21 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (   33) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: (   1) minutes.
Extended self-test routine
recommended polling time: (   1) minutes.
Conveyance self-test routine
recommended polling time: (   1) minutes.
SCT capabilities:        (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       763
 12 Power_Cycle_Count       0x0012   100   100   000    Old_age   Always       -       242
167 Unknown_Attribute       0x0022   100   100   000    Old_age   Always       -       0
168 Unknown_Attribute       0x0012   100   100   000    Old_age   Always       -       4
169 Unknown_Attribute       0x0013   093   093   010    Pre-fail  Always       -       257701970367
173 Unknown_Attribute       0x0012   200   200   000    Old_age   Always       -       30066540559
175 Program_Fail_Count_Chip 0x0013   040   100   010    Pre-fail  Always       -       0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033   093   093   020    Pre-fail  Always       -       852
192 Power-Off_Retract_Count 0x0012   100   100   000    Old_age   Always       -       31
194 Temperature_Celsius     0x0022   066   066   030    Old_age   Always       -       34 (Min/Max 33/40)
231 Temperature_Celsius     0x0033   094   094   005    Pre-fail  Always       -       1536
233 Media_Wearout_Indicator 0x0032   100   100   000    Old_age   Always       -       3387088512
234 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       1606804930560
241 Total_LBAs_Written      0x0032   100   100   000    Old_age   Always       -       2724954965
242 Total_LBAs_Read         0x0032   100   100   000    Old_age   Always       -       3829255297

SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:42:32.800  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:42:27.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:42:27.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:42:27.500  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:42:27.500  SET FEATURES [Enable SATA feature]

Error 9 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:41:49.300  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:41:43.900  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:41:43.900  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:41:43.900  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:41:43.900  SET FEATURES [Enable SATA feature]

Error 8 occurred at disk power-on lifetime: 759 hours (31 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 00 00 00 a0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  ec 00 00 00 00 00 a0 08      00:04:34.500  IDENTIFY DEVICE
  ef 10 02 00 00 00 a0 08      00:04:29.200  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:04:29.200  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:04:29.200  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:04:29.200  SET FEATURES [Enable SATA feature]

Error 7 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 80 f9 a0 e1  Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 80 f9 a0 e1 08      00:05:28.500  READ DMA
  ca 00 28 18 df a1 e1 08      00:05:28.500  WRITE DMA
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:05:28.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:05:28.500  SET FEATURES [Set transfer mode]

Error 6 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 80 f9 a0 e1  Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 80 f9 a0 e1 08      00:05:28.500  READ DMA
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]
  ec 00 00 00 00 00 a0 08      00:05:28.500  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 08      00:05:28.500  SET FEATURES [Set transfer mode]
  ef 10 02 00 00 00 a0 08      00:05:28.500  SET FEATURES [Enable SATA feature]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%       763         -
# 2  Extended offline    Completed without error       00%       763         -
# 3  Extended offline    Completed without error       00%       760         -
# 4  Short offline       Completed without error       00%       759         -
# 5  Short offline       Completed without error       00%       754         -
# 6  Short offline       Completed without error       00%       412         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Název: Re:SSD disk
Přispěvatel: Kylo 30. 11. 2018, 21:50:51
Smart na SSD ? To jako proc ?
Název: Re:SSD disk
Přispěvatel: Lol Phirae 30. 11. 2018, 22:17:06
Smart na SSD ? To jako proc ?

Překvapivě některý lidi rádi monitorujou disky a objednaj si nový, než jim ten stávající chcípne.  ::)
Název: Re:Stav SSD pomocí smartctl
Přispěvatel: Jan Forman 30. 11. 2018, 23:02:06
Mám velmi špatné zkušenosti se SMART hodnotama z různých SSD, často jsou nelogické. Řadiče nebo SW očekávají zcela odlišné hodnoty a pak drze hlásí "stav 100%" a disk je v háji.
Tak se řídím jen hodnotou kolik je zapsáno dat a typem disku (MLC, TLC).

Tenhle má zapsáno asi 1.27 TB což je hodně málo. Ty chyby co píše mi příjdou spíš jako kdyby od něj nějaký SW chtěl cosi nestandardního.
Název: Re:Stav SSD pomocí smartctl
Přispěvatel: trubicoid2 30. 11. 2018, 23:36:58
přijde mi to jako vadnej kabel? nebo řadič?
Název: Re:SSD disk
Přispěvatel: Kylo 30. 11. 2018, 23:46:48
Smart na SSD ? To jako proc ?

Překvapivě některý lidi rádi monitorujou disky a objednaj si nový, než jim ten stávající chcípne.  ::)

Bejvavalo v minulem tisicileti. Dneska jsou SSD naletovany na zakladovce.
Název: Re:SSD disk
Přispěvatel: Lol Phirae 30. 11. 2018, 23:52:07
Bejvavalo v minulem tisicileti. Dneska jsou SSD naletovany na zakladovce.

Že si kupuješ naletovaný kokotiny, to je tvůj problém.