Blbne mě disk ale nedokážu se orientovat ve výpisu smartctl, poradil by mě někdo jestli umírá nebo ne?
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ADATA SU700
Serial Number: 2H2320062333
LU WWN Device Id: 5 707c18 10050c4d5
Firmware Version: B170428a
User Capacity: 240,057,409,536 bytes [240 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Nov 30 20:49:21 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 33) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 1) minutes.
Conveyance self-test routine
recommended polling time: ( 1) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 763
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 242
167 Unknown_Attribute 0x0022 100 100 000 Old_age Always - 0
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 4
169 Unknown_Attribute 0x0013 093 093 010 Pre-fail Always - 257701970367
173 Unknown_Attribute 0x0012 200 200 000 Old_age Always - 30066540559
175 Program_Fail_Count_Chip 0x0013 040 100 010 Pre-fail Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 093 093 020 Pre-fail Always - 852
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 31
194 Temperature_Celsius 0x0022 066 066 030 Old_age Always - 34 (Min/Max 33/40)
231 Temperature_Celsius 0x0033 094 094 005 Pre-fail Always - 1536
233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 3387088512
234 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1606804930560
241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 2724954965
242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 3829255297
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:42:32.800 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:42:27.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:42:27.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:42:27.500 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:42:27.500 SET FEATURES [Enable SATA feature]
Error 9 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:41:49.300 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:41:43.900 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:41:43.900 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:41:43.900 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:41:43.900 SET FEATURES [Enable SATA feature]
Error 8 occurred at disk power-on lifetime: 759 hours (31 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:04:34.500 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:04:29.200 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:04:29.200 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:04:29.200 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:04:29.200 SET FEATURES [Enable SATA feature]
Error 7 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 80 f9 a0 e1 Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 f9 a0 e1 08 00:05:28.500 READ DMA
ca 00 28 18 df a1 e1 08 00:05:28.500 WRITE DMA
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:05:28.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:28.500 SET FEATURES [Set transfer mode]
Error 6 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 80 f9 a0 e1 Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 f9 a0 e1 08 00:05:28.500 READ DMA
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:05:28.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:28.500 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 763 -
# 2 Extended offline Completed without error 00% 763 -
# 3 Extended offline Completed without error 00% 760 -
# 4 Short offline Completed without error 00% 759 -
# 5 Short offline Completed without error 00% 754 -
# 6 Short offline Completed without error 00% 412 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
6 Odpovědí
2170 Zhlédnutí