Divné SMART hodnoty nového disku

Divné SMART hodnoty nového disku
« kdy: 09. 05. 2014, 16:18:51 »
Mám chvilku nový disk ale smartctl hlásí divné hodnoty. čísla odpovídají tomu že je nový (počet zapnutí, vadné sektory, najeté hodiny...) ale přitom hlásí že brzo odejde do křemíkového nebe. Je opravdu disk v ... a mám ho reklamovat nebo to ignorovat?
výstup smartctl

Kód: [Vybrat]
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.13.0-24-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Device Model:     WDC WD1003FZEX-00MK2A0
Serial Number:    WD-WCC3F4704007
LU WWN Device Id: 5 0014ee 25f7ca053
Firmware Version: 01.01A01
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Fri May  9 15:41:31 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12060) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: (   2) minutes.
Extended self-test routine
recommended polling time: ( 125) minutes.
Conveyance self-test routine
recommended polling time: (   5) minutes.
SCT capabilities:        (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x002f   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0027   170   170   021    Pre-fail  Always       -       2475
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       18
  5 Reallocated_Sector_Ct   0x0033   200   200   140    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x002e   200   200   000    Old_age   Always       -       0
  9 Power_On_Hours          0x0032   100   100   000    Old_age   Always       -       36
 10 Spin_Retry_Count        0x0032   100   253   000    Old_age   Always       -       0
 11 Calibration_Retry_Count 0x0032   100   253   000    Old_age   Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       18
192 Power-Off_Retract_Count 0x0032   200   200   000    Old_age   Always       -       1
193 Load_Cycle_Count        0x0032   200   200   000    Old_age   Always       -       16
194 Temperature_Celsius     0x0022   114   107   000    Old_age   Always       -       29
196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0032   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   253   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0008   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
« Poslední změna: 09. 05. 2014, 22:12:50 od Petr Krčmář »


Heh

Re:Divne SMART hodnoty disku
« Odpověď #1 kdy: 09. 05. 2014, 16:23:25 »
A kdeže to má hlásit, že odejde?

Re:Divne SMART hodnoty disku
« Odpověď #2 kdy: 09. 05. 2014, 16:33:13 »
Kód: [Vybrat]
...
  1 Raw_Read_Error_Rate     0x002f   200   200   051    [b]Pre-fail[/b]  Always       -       0
  3 Spin_Up_Time            0x0027   170   170   021    [b]Pre-fail[/b]  Always       -       2475
  4 Start_Stop_Count        0x0032   100   100   000    [b]Old_age[/b]   Always       -       18
...

Gnome disk a widle7 taky.

trubicoid2

Re:Divne SMART hodnoty disku
« Odpověď #3 kdy: 09. 05. 2014, 16:36:30 »
ale přitom hlásí že brzo odejde do křemíkového nebe

a to vidis kde? ten spin-up time je akorat nejakej velkej, rozjizdi se dlouho? jestli jo, tak ho vymen
na samsungu f3 se musel udelat nejakej fw update a pak to nabihalo rychleji

udelej mu test, nejlip dlouhej
Kód: [Vybrat]
smartctl -t long /dev/sda
a az dobehne, tak posli vysledek

hu

Re:Divne SMART hodnoty disku
« Odpověď #4 kdy: 09. 05. 2014, 16:38:46 »
Kód: [Vybrat]
...
  1 Raw_Read_Error_Rate     0x002f   200   200   051    [b]Pre-fail[/b]  Always       -       0
  3 Spin_Up_Time            0x0027   170   170   021    [b]Pre-fail[/b]  Always       -       2475
  4 Start_Stop_Count        0x0032   100   100   000    [b]Old_age[/b]   Always       -       18
...

Gnome disk a widle7 taky.

Ale houby, jedná se o označení typu daného parametru. Zatímco některé jsou spojené s dlouhým věkem (Old_age parametry), jiné indikují pre-fail stav. Nicméně jejich hodnoty jsou zcela v pořádku. 18 start-stop cyklů asi těžko bude indikovat nějaké velké stáří disku.