# smartctl -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net=== START OF INFORMATION SECTION ===
Model Family: Western Digital AV-GP family
Device Model: WDC WD15EVDS-68V9B0
Serial Number: WD-WMAVU0931943
Firmware Version: 01.00A01
User Capacity: 1,500,300,828,160 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Aug 22 20:45:23 2012 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (35700) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 1700
3 Spin_Up_Time 0x0027 189 180 021 Pre-fail Always - 5508
4 Start_Stop_Count 0x0032 080 080 000 Old_age Always - 20552
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 071 071 000 Old_age Always - 21623
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 080 080 000 Old_age Always - 20550
192 Power-Off_Retract_Count 0x0032 173 173 000 Old_age Always - 20541
193 Load_Cycle_Count 0x0032 156 156 000 Old_age Always - 132097
194 Temperature_Celsius 0x0022 106 103 000 Old_age Always - 44
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 199 199 000 Old_age Always - 330
198 Offline_Uncorrectable 0x0030 199 199 000 Old_age Offline - 255
199 UDMA_CRC_Error_Count 0x0032 200 199 000 Old_age Always - 4931
200 Multi_Zone_Error_Rate 0x0008 198 198 000 Old_age Offline - 410
SMART Error Log Version: 1
ATA Error Count: 699 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 699 occurred at disk power-on lifetime: 21615 hours (900 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 39 40 e3 Error: UNC at LBA = 0x03403908 = 54540552
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ff 38 40 e3 08 14:06:15.378 READ DMA
ec 00 00 00 00 00 a0 08 14:06:15.371 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 14:06:15.371 SET FEATURES [Set transfer mode]
Error 698 occurred at disk power-on lifetime: 21615 hours (900 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 39 40 e3 Error: UNC at LBA = 0x03403908 = 54540552
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ff 38 40 e3 08 14:06:12.690 READ DMA
ec 00 00 00 00 00 a0 08 14:06:12.682 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 14:06:12.682 SET FEATURES [Set transfer mode]
Error 697 occurred at disk power-on lifetime: 21615 hours (900 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 39 40 e3 Error: UNC at LBA = 0x03403908 = 54540552
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ff 38 40 e3 08 14:06:10.017 READ DMA
ec 00 00 00 00 00 a0 08 14:06:10.009 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 14:06:10.009 SET FEATURES [Set transfer mode]
Error 696 occurred at disk power-on lifetime: 21615 hours (900 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 39 40 e3 Error: UNC at LBA = 0x03403908 = 54540552
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ff 38 40 e3 08 14:06:07.344 READ DMA
ec 00 00 00 00 00 a0 08 14:06:07.336 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 14:06:07.336 SET FEATURES [Set transfer mode]
Error 695 occurred at disk power-on lifetime: 21615 hours (900 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 08 39 40 e3 Error: UNC at LBA = 0x03403908 = 54540552
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 00 ff 38 40 e3 08 14:06:04.671 READ DMA
ec 00 00 00 00 00 a0 08 14:06:04.663 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 14:06:04.663 SET FEATURES [Set transfer mode]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 21617 485393
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Zobrazit příspěvky
