Zobrazit příspěvky
16
Hardware / Re:pwmconfig a větráky jedou jako o život
« kdy: 16. 11. 2020, 09:22:31 »Co sem alespoň postnout ten konfigurák?
Ono tam nic nakonfigurovat nešlo...
Kód: [Vybrat]
a@linux:~$ sudo pwmconfig
# pwmconfig version 3.6.0
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
Found the following devices:
hwmon0 is acpitz
hwmon1 is coretemp
hwmon2/device is f71808a
Found the following PWM controls:
hwmon2/device/pwm1 current value: 255
hwmon2/device/pwm2 current value: 255
hwmon2/device/pwm3 current value: 255
Giving the fans some time to reach full speed...
Found the following fan sensors:
hwmon2/device/fan1_input current speed: 2546 RPM
hwmon2/device/fan2_input current speed: 4504 RPM
hwmon2/device/fan3_input current speed: 0 ... skipping!
Warning!!! This program will stop your fans, one at a time,
for approximately 5 seconds each!!!
This may cause your processor temperature to rise!!!
If you do not want to do this hit control-C now!!!
Hit return to continue:
Testing pwm control hwmon2/device/pwm1 ...
hwmon2/device/fan1_input ... speed was 2546 now 2495
no correlation
hwmon2/device/fan2_input ... speed was 4504 now 4531
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/device/pwm1,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing pwm control hwmon2/device/pwm2 ...
hwmon2/device/fan1_input ... speed was 2546 now 2590
no correlation
hwmon2/device/fan2_input ... speed was 4504 now 4178
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/device/pwm2,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing pwm control hwmon2/device/pwm3 ...
hwmon2/device/fan1_input ... speed was 2546 now 2590
no correlation
hwmon2/device/fan2_input ... speed was 4504 now 4504
no correlation
No correlations were detected.
There is either no fan connected to the output of hwmon2/device/pwm3,
or the connected fan has no rpm-signal connected to one of
the tested fan sensors. (Note: not all motherboards have
the pwm outputs connected to the fan connectors,
check out the hardware database on http://www.almico.com/forumindex.php)
Did you see/hear a fan stopping during the above test (n)? n
Testing is complete.
Please verify that all fans have returned to their normal speed.
The fancontrol script can automatically respond to temperature changes
of your system by changing fanspeeds.
Do you want to set up its configuration file now (y)? y
What should be the path to your fancontrol config file (/etc/fancontrol)? /home/
Select fan output to configure, or other action:
1) Change INTERVAL 3) Save and quit
2) Just quit 4) Show configuration
select (1-n): 4
Common Settings:
INTERVAL=10
Select fan output to configure, or other action:
1) Change INTERVAL 3) Save and quit
2) Just quit 4) Show configuration
select (1-n): 3
Saving configuration to /etc/fancontrol...
Configuration saved
a@linux:~$ sudo fancontrol
[sudo] heslo pro a:
Loading configuration from /etc/fancontrol ...
Some mandatory settings missing, please check your config file!Kód: [Vybrat]
a@linux:~$ cat fancontrol
# Configuration file generated by pwmconfig, changes will be lost
INTERVAL=10
DEVPATH=
DEVNAME=
FCTEMPS=
FCFANS=
MINTEMP=
MAXTEMP=
MINSTART=
MINSTOP=
Servisa běží?
Jaké jsou teploty a jaké jsou rychlosti?
Nevím co je servisa.
Minimální zátěž:
Kód: [Vybrat]
a@linux:~$ sensors
f71808a-isa-0290
Adapter: ISA adapter
+3.3V: 3.31 V
in1: 1.70 V
in2: 1.03 V
in3: 1.47 V
3VSB: 3.34 V
Vbat: 3.28 V
fan1: 1427 RPM
fan2: 2546 RPM
fan3: 0 RPM ALARM
temp1: +28.0°C (high = +85.0°C, hyst = +81.0°C)
(crit = +100.0°C, hyst = +96.0°C) sensor = transistor
temp2: +33.0°C (high = +85.0°C, hyst = +81.0°C)
(crit = +100.0°C, hyst = +96.0°C) sensor = transistor
acpitz-acpi-0
Adapter: ACPI interface
temp1: +27.8°C (crit = +105.0°C)
temp2: +29.8°C (crit = +105.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Package id 0: +32.0°C (high = +80.0°C, crit = +100.0°C)
Core 0: +28.0°C (high = +80.0°C, crit = +100.0°C)
Core 1: +29.0°C (high = +80.0°C, crit = +100.0°C)
Core 2: +28.0°C (high = +80.0°C, crit = +100.0°C)
Core 3: +27.0°C (high = +80.0°C, crit = +100.0°C)
Udělal jsem ten CMOS reset a pomohlo to tak napůl. Jak vidíte nahoře, už je to jen 1500 a 2500 RPM, no než jsem spustil pwmconfig, tak to bývalo 1000 a 1500. Lepší by bylo méně, ale asi to tak raději už nechám.
