Témata

1

Hardware / Můžu podle výsledků SMART vyhodit tento disk

« kdy: 11. 09. 2024, 21:35:28 »

magnety samozrejme vyberem!

Kód: [Vybrat]

smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.6.47-gentoo-dist] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org
 
=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST2000DM001-1ER164
Serial Number:    Z4Z3M0N3
LU WWN Device Id: 5 000c50 08700cbd7
Firmware Version: CC26
User Capacity:    2,000,398,934,016 bytes [2.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Sep 11 21:15:07 2024 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
 
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
 
General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status:      ( 248) Self-test routine in progress...
80% of test remaining.
Total time to complete Offline
data collection: (   80) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: (   1) minutes.
Extended self-test routine
recommended polling time: ( 216) minutes.
Conveyance self-test routine
recommended polling time: (   2) minutes.
SCT capabilities:        (0x1085) SCT Status supported.
 
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   099   006    Pre-fail  Always       -       154796888
  3 Spin_Up_Time            0x0003   096   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   099   099   020    Old_age   Always       -       1156
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       56
  7 Seek_Error_Rate         0x000f   072   060   030    Pre-fail  Always       -       16130225
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       1886
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   099   099   020    Old_age   Always       -       1146
183 Runtime_Bad_Block       0x0032   100   100   000    Old_age   Always       -       0
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   066   066   000    Old_age   Always       -       34
188 Command_Timeout         0x0032   100   100   000    Old_age   Always       -       0 0 0
189 High_Fly_Writes         0x003a   088   088   000    Old_age   Always       -       12
190 Airflow_Temperature_Cel 0x0022   063   054   045    Old_age   Always       -       37 (Min/Max 22/40)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       169
193 Load_Cycle_Count        0x0032   093   093   000    Old_age   Always       -       14532
194 Temperature_Celsius     0x0022   037   046   000    Old_age   Always       -       37 (0 17 0 0 0)
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       1478h+09m+27.378s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       30097244763
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       70948224161
 
SMART Error Log Version: 1
ATA Error Count: 34 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
 
Error 34 occurred at disk power-on lifetime: 1860 hours (77 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 53 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      11:11:04.424  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      11:11:04.410  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 e0 00      11:11:04.384  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      11:11:04.383  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      11:11:04.371  SET FEATURES [Set transfer mode]
 
Error 33 occurred at disk power-on lifetime: 1860 hours (77 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 53 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      11:11:00.658  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      11:11:00.648  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 e0 00      11:11:00.622  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      11:11:00.621  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      11:11:00.609  SET FEATURES [Set transfer mode]
 
Error 32 occurred at disk power-on lifetime: 1860 hours (77 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 53 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      11:10:56.879  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      11:10:56.868  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 e0 00      11:10:56.841  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      11:10:56.841  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      11:10:56.828  SET FEATURES [Set transfer mode]
 
Error 31 occurred at disk power-on lifetime: 1860 hours (77 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 53 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      11:10:53.115  READ FPDMA QUEUED
  ef 10 02 00 00 00 a0 00      11:10:53.105  SET FEATURES [Enable SATA feature]
  27 00 00 00 00 00 e0 00      11:10:53.079  READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
  ec 00 00 00 00 00 a0 00      11:10:53.078  IDENTIFY DEVICE
  ef 03 46 00 00 00 a0 00      11:10:53.066  SET FEATURES [Set transfer mode]
 
Error 30 occurred at disk power-on lifetime: 1860 hours (77 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.
 
  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 53 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455
 
  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      11:10:49.228  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      11:10:49.192  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      11:10:48.391  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      11:10:48.377  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      11:10:48.376  READ FPDMA QUEUED
 
SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Self-test routine in progress 80%      1886         -
# 2  Short offline       Completed without error       00%      1652         -
# 3  Short offline       Completed without error       00%      1404         -
# 4  Extended offline    Completed without error       00%         3         -
# 5  Short offline       Completed without error       00%         0         -
 
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
 
The above only provides legacy SMART information - try 'smartctl -x' for more

2

Hardware / Update BIOS na Fujitsu LifeBook E5512

« kdy: 26. 08. 2024, 16:39:59 »

laptop mi bezi s linuxom. vytvoril som windowsPE kluc ktory nabootuje vpho tam som pustil admin pack od Fujitsu pre update BIOSu.
zial moje zariadenie nebolo rozpoznane. podla toho co som nasiel to bude asi tym ze winPE neobsahuje BIOS driver pre Fujitsu.

pokial niekto vie ako sa pracuje s WinPE dajte mi vediet ako tam ten driver dostanem.

3

Windows a jiné systémy / Antivirus pro Windows zadarmo

« kdy: 19. 03. 2024, 13:43:13 »

na jednom windows hoste vypsala rocna licencia antiviru co tam bol nainstalovany OEM.
tak som ho odinstaloval s tym ze tam hodim windows defender - a ono to po mne chce nejaku Office 365 subscription...
existuje v dnesnej dobe este nejaky pouzitelny antivirus na windows zadarmo?

4

Hardware / Odchadzí mi podle logu SSD?

« kdy: 10. 02. 2024, 18:31:37 »

ja jen ze mi to hlasi orphaned inodes v EXT4 po soft rebootoch.
ad Unsafe Shutdowns: to bolo vtedy ked som updatoval FW pomocou vybornej Samsung utility ktora zial nepodporuje UEFI :facepalm:
ad Smart: Invalid Field in Command
ad FW: 2B2QEXM7 way too old

ako neriesil by som to ale ked mi odchadza FS...

Kód: [Vybrat]

# smartctl --all /dev/nvme0
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.7.4-artix1-1] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Number:                       Samsung SSD 970 EVO Plus 2TB
Serial Number:                      S4J4NM0W609377M
Firmware Version:                   2B2QEXM7
PCI Vendor/Subsystem ID:            0x144d
IEEE OUI Identifier:                0x002538
Total NVM Capacity:                 2,000,398,934,016 [2.00 TB]
Unallocated NVM Capacity:           0
Controller ID:                      4
NVMe Version:                       1.3
Number of Namespaces:               1
Namespace 1 Size/Capacity:          2,000,398,934,016 [2.00 TB]
Namespace 1 Utilization:            198,313,590,784 [198 GB]
Namespace 1 Formatted LBA Size:     512
Namespace 1 IEEE EUI-64:            002538 56319173a9
Local Time is:                      Fri Feb  9 22:21:57 2024 CET
Firmware Updates (0x16):            3 Slots, no Reset required
Optional Admin Commands (0x0017):   Security Format Frmw_DL Self_Test
Optional NVM Commands (0x005f):     Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp
Log Page Attributes (0x03):         S/H_per_NS Cmd_Eff_Lg
Maximum Data Transfer Size:         512 Pages
Warning  Comp. Temp. Threshold:     85 Celsius
Critical Comp. Temp. Threshold:     85 Celsius

Supported Power States
St Op     Max   Active     Idle   RL RT WL WT  Ent_Lat  Ex_Lat
 0 +     7.50W       -        -    0  0  0  0        0       0
 1 +     5.90W       -        -    1  1  1  1        0       0
 2 +     3.60W       -        -    2  2  2  2        0       0
 3 -   0.0700W       -        -    3  3  3  3      210    1200
 4 -   0.0050W       -        -    4  4  4  4     2000    8000

Supported LBA Sizes (NSID 0x1)
Id Fmt  Data  Metadt  Rel_Perf
 0 +     512       0         0

=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

SMART/Health Information (NVMe Log 0x02)
Critical Warning:                   0x00
Temperature:                        34 Celsius
Available Spare:                    100%
Available Spare Threshold:          10%
Percentage Used:                    0%
Data Units Read:                    155,454 [79.5 GB]
Data Units Written:                 2,361,653 [1.20 TB]
Host Read Commands:                 1,500,387
Host Write Commands:                31,692,814
Controller Busy Time:               103
Power Cycles:                       12
Power On Hours:                     88
Unsafe Shutdowns:                   6
Media and Data Integrity Errors:    0
Error Information Log Entries:      23
Warning  Comp. Temperature Time:    0
Critical Comp. Temperature Time:    0
Temperature Sensor 1:               34 Celsius
Temperature Sensor 2:               29 Celsius

Error Information (NVMe Log 0x01, 16 of 64 entries)
Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS  Message
  0         23     0  0x000c  0x4004      -            0     0     -  Invalid Field in Command

Self-test Log (NVMe Log 0x06)
Self-test status: No self-test in progress
Num  Test_Description  Status                       Power_on_Hours  Failing_LBA  NSID Seg SCT Code
 0   Extended          Completed without error                  86            -     -   -   -    -
 1   Short             Completed without error                  86            -     -   -   -    -

nexus:[root]:/home/erik# smartctl --all /dev/nvme0
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.7.4-artix1-1] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Number:                       Samsung SSD 970 EVO Plus 2TB
Serial Number:                      S4J4NM0W609377M
Firmware Version:                   2B2QEXM7
PCI Vendor/Subsystem ID:            0x144d
IEEE OUI Identifier:                0x002538
Total NVM Capacity:                 2,000,398,934,016 [2.00 TB]
Unallocated NVM Capacity:           0
Controller ID:                      4
NVMe Version:                       1.3
Number of Namespaces:               1
Namespace 1 Size/Capacity:          2,000,398,934,016 [2.00 TB]
Namespace 1 Utilization:            198,580,367,360 [198 GB]
Namespace 1 Formatted LBA Size:     512
Namespace 1 IEEE EUI-64:            002538 56319173a9
Local Time is:                      Sat Feb 10 11:46:56 2024 CET
Firmware Updates (0x16):            3 Slots, no Reset required
Optional Admin Commands (0x0017):   Security Format Frmw_DL Self_Test
Optional NVM Commands (0x005f):     Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp
Log Page Attributes (0x03):         S/H_per_NS Cmd_Eff_Lg
Maximum Data Transfer Size:         512 Pages
Warning  Comp. Temp. Threshold:     85 Celsius
Critical Comp. Temp. Threshold:     85 Celsius

Supported Power States
St Op     Max   Active     Idle   RL RT WL WT  Ent_Lat  Ex_Lat
 0 +     7.50W       -        -    0  0  0  0        0       0
 1 +     5.90W       -        -    1  1  1  1        0       0
 2 +     3.60W       -        -    2  2  2  2        0       0
 3 -   0.0700W       -        -    3  3  3  3      210    1200
 4 -   0.0050W       -        -    4  4  4  4     2000    8000

Supported LBA Sizes (NSID 0x1)
Id Fmt  Data  Metadt  Rel_Perf
 0 +     512       0         0

=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

SMART/Health Information (NVMe Log 0x02)
Critical Warning:                   0x00
Temperature:                        35 Celsius
Available Spare:                    100%
Available Spare Threshold:          10%
Percentage Used:                    0%
Data Units Read:                    155,472 [79.6 GB]
Data Units Written:                 2,368,377 [1.21 TB]
Host Read Commands:                 1,500,769
Host Write Commands:                31,835,232
Controller Busy Time:               104
Power Cycles:                       12
Power On Hours:                     89
Unsafe Shutdowns:                   6
Media and Data Integrity Errors:    0
Error Information Log Entries:      23
Warning  Comp. Temperature Time:    0
Critical Comp. Temperature Time:    0
Temperature Sensor 1:               35 Celsius
Temperature Sensor 2:               31 Celsius

Error Information (NVMe Log 0x01, 16 of 64 entries)
Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS  Message
  0         23     0  0x000c  0x4004      -            0     0     -  Invalid Field in Command

Self-test Log (NVMe Log 0x06)
Self-test status: No self-test in progress
Num  Test_Description  Status                       Power_on_Hours  Failing_LBA  NSID Seg SCT Code
 0   Extended          Completed without error                  86            -     -   -   -    -
 1   Short             Completed without error                  86            -     -   -   -    -

nexus:[root]:/home/erik# smartctl --all /dev/nvme0
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.7.4-artix1-1] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Number:                       Samsung SSD 970 EVO Plus 2TB
Serial Number:                      S4J4NM0W609377M
Firmware Version:                   2B2QEXM7
PCI Vendor/Subsystem ID:            0x144d
IEEE OUI Identifier:                0x002538
Total NVM Capacity:                 2,000,398,934,016 [2.00 TB]
Unallocated NVM Capacity:           0
Controller ID:                      4
NVMe Version:                       1.3
Number of Namespaces:               1
Namespace 1 Size/Capacity:          2,000,398,934,016 [2.00 TB]
Namespace 1 Utilization:            198,860,980,224 [198 GB]
Namespace 1 Formatted LBA Size:     512
Namespace 1 IEEE EUI-64:            002538 56319173a9
Local Time is:                      Sat Feb 10 15:05:01 2024 CET
Firmware Updates (0x16):            3 Slots, no Reset required
Optional Admin Commands (0x0017):   Security Format Frmw_DL Self_Test
Optional NVM Commands (0x005f):     Comp Wr_Unc DS_Mngmt Wr_Zero Sav/Sel_Feat Timestmp
Log Page Attributes (0x03):         S/H_per_NS Cmd_Eff_Lg
Maximum Data Transfer Size:         512 Pages
Warning  Comp. Temp. Threshold:     85 Celsius
Critical Comp. Temp. Threshold:     85 Celsius

Supported Power States
St Op     Max   Active     Idle   RL RT WL WT  Ent_Lat  Ex_Lat
 0 +     7.50W       -        -    0  0  0  0        0       0
 1 +     5.90W       -        -    1  1  1  1        0       0
 2 +     3.60W       -        -    2  2  2  2        0       0
 3 -   0.0700W       -        -    3  3  3  3      210    1200
 4 -   0.0050W       -        -    4  4  4  4     2000    8000

Supported LBA Sizes (NSID 0x1)
Id Fmt  Data  Metadt  Rel_Perf
 0 +     512       0         0

=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

SMART/Health Information (NVMe Log 0x02)
Critical Warning:                   0x00
Temperature:                        35 Celsius
Available Spare:                    100%
Available Spare Threshold:          10%
Percentage Used:                    0%
Data Units Read:                    155,474 [79.6 GB]
Data Units Written:                 2,370,175 [1.21 TB]
Host Read Commands:                 1,500,796
Host Write Commands:                31,869,869
Controller Busy Time:               104
Power Cycles:                       12
Power On Hours:                     89
Unsafe Shutdowns:                   6
Media and Data Integrity Errors:    0
Error Information Log Entries:      23
Warning  Comp. Temperature Time:    0
Critical Comp. Temperature Time:    0
Temperature Sensor 1:               35 Celsius
Temperature Sensor 2:               31 Celsius

Error Information (NVMe Log 0x01, 16 of 64 entries)
Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS  Message
  0         23     0  0x000c  0x4004      -            0     0     -  Invalid Field in Command

Self-test Log (NVMe Log 0x06)
Self-test status: No self-test in progress
Num  Test_Description  Status                       Power_on_Hours  Failing_LBA  NSID Seg SCT Code
 0   Extended          Completed without error                  86            -     -   -   -    -
 1   Short             Completed without error                  86            -     -   -   -    -


Kód: [Vybrat]

# fwupdmgr get-devices
├─SSD 970 EVO Plus 2TB:
│     Device ID:          04e17fcf7d3de91da49a163ffe4907855c3648be
│     Summary:            NVM Express solid state drive
│     Current version:    2B2QEXM7
│     Vendor:             Samsung (NVME:0x144D)
│     Serial Number:      S4J4NM0W609377M
│     GUIDs:              47335265-a509-51f7-841e-1c94911af66b ← NVME\VEN_144D&DEV_A808
│                         c9d531ea-ee7d-5562-8def-c64d0d144813 ← NVME\VEN_144D&DEV_A808&SUBSYS_144DA801
│                         66cc31b5-6dc4-55da-9008-bf73c91a0826 ← Samsung SSD 970 EVO Plus 2TB
│     Device Flags:       • Internal device
│                         • Updatable
│                         • System requires external power source
│                         • Needs a reboot after installation
│                         • Device is usable for the duration of the update
│                         • Signed Payload


5

Software / Hledám pixelovou skákačku ze Steamu

« kdy: 31. 01. 2024, 16:46:49 »

minuly rok som videl pravdepodobne na root.cz nejaku pixelovu jump and run hru ktora bola dostupna cez steam a teraz si neviem spomenut ako sa to volalo.

Hra bola pixel artova a mala pokial si dobre pamatam dobru AI co sa tyka oponentov. Oponenti vyzerali ako selmy

Prosim ak viete asi o com hovorim tak mi to sem postnite. Moje google fu na toto ocividne nestaci.

6

Software / Hledání minerů v hrách

« kdy: 25. 12. 2023, 20:02:54 »

kupil som synovy hru: https://store.steampowered.com/app/1624540/Storyteller/
hrali sme to tak hodku 2. zacal som citit spalene plasty tak som chytil bednu. bola zerava...

ta hra nema preco vytazovat grafiku/cpu ale robi to. mate niekto skusenost s touto hrou?

tech spec: amd buldozer / amd radeon nejaka 4gb ram.

7

Hardware / Regulace nabíjení trvale připojeného notebooku

« kdy: 05. 12. 2023, 21:14:58 »

mam novy laptop a bezi 24x7 - restarty pri kernel upgrade. da sa nastavit nabijanie baterky tak aby sa pri 10% zacalo nabijat a pri 90% prestalo?

pouzivam artix a xfce.

8

/dev/null / spehovanie uzivatelov cez intel gpu driver

« kdy: 19. 08. 2023, 16:40:03 »

celkom zaujimavy clanok: https://www.extremetech.com/gaming/intels-gpu-drivers-now-collect-telemetry-including-how-you-use-your-computer

sorry nechce sa mi to prekladat do spravicky tak len sem...

9

Hardware / Skákající touchpad na starém Dell Latitude

« kdy: 09. 05. 2023, 18:19:20 »

mám zapnutý laptop furt. po nejakej dobe opakovane my zacne blbnúť touchpad. kurzor pri pohybe na touchpade skáče a je neovládatelný.
inštalácia je arch linux. xorg.conf som nijak neupravoval.

na xorg logoch ma zaujalo toto:

Kód: [Vybrat]

[    12.539] (II) event8  - AlpsPS/2 ALPS GlidePoint: no resolution or size hints, assuming a size of 69x50mm
no nič idem dalej gúgliť.

10

Odkladiště / Nejde mi Discord

« kdy: 13. 04. 2023, 19:45:59 »

po prihlaseni na discord mi hlasi: aw this is awkward...
smazal sem kookies a updatol firefox. restartol komp a povolil neco v noscripte.
este idem skusit chromium uz ma nic nenapada.

11

/dev/null / setuid jako hrozba?

« kdy: 17. 03. 2023, 18:14:06 »

https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.103&id=1639a49ccdce58ea248841ed9b23babcce6dbb0b

12

/dev/null / potrebujete "nove" fonty?

« kdy: 29. 01. 2022, 20:22:55 »

https://int10h.org/oldschool-pc-fonts/
odporucam IBM XGA-AI 7x15

13

Server / Mazanie duplicit v Icinga db - zlepšenie sub selectu

« kdy: 10. 05. 2021, 09:43:02 »

Ahoj,

musim pomazat duplicity (bug) v icinga_commenthistory (5000000 zaznamov).

Vymyslel som to tak ze zistim maximalne id v subselecte a tieto ID nebudem mazat. Zial bezi to neskutocne dlho.

Kód: [Vybrat]

select max(commenthistory_id)
from icinga_commenthistory
group by comment_time, comment_data
Nejaky napad jak toto urychlit?

14

Windows a jiné systémy / Alternativní klient pro Hangouts na F-Droidu

« kdy: 13. 03. 2021, 18:04:36 »

Xabber mi sa sice pripoji na google hangouts ale niekedy neposiela spravy (cervene x pri spravach).
Skusal som este yaxim ten bol pouzitelnejsi ked nic nenajdeme tak pouzijem to. nechce skusat kazdu aplikaciu na f-droide.

15

/dev/null / gentoo.org neni dostupne

« kdy: 12. 02. 2020, 20:48:50 »

Kód: [Vybrat]

scramble@debian:~$ ping forums.gentoo.org
PING gossamer-ipvs-forums-v4v6.gentoo.org (204.187.15.12) 56(84) bytes of data.
^C64 bytes from 204.187.15.12: icmp_seq=2 ttl=55 time=307 ms

--- gossamer-ipvs-forums-v4v6.gentoo.org ping statistics ---
2 packets transmitted, 1 received, 50% packet loss, time 15ms
rtt min/avg/max/mdev = 307.204/307.204/307.204/0.000 ms
scramble@debian:~$ ping gentoo.org
PING gentoo.org (89.16.167.134) 56(84) bytes of data.
64 bytes from www.gentoo.org (89.16.167.134): icmp_seq=5 ttl=53 time=149 ms
64 bytes from www.gentoo.org (89.16.167.134): icmp_seq=7 ttl=53 time=140 ms
^C
--- gentoo.org ping statistics ---
11 packets transmitted, 2 received, 81.8182% packet loss, time 193ms
rtt min/avg/max/mdev = 139.686/144.245/148.805/4.575 ms