1
Software / Re:Čím nahradit Stocard?
« kdy: 12. 09. 2024, 10:26:56 »
Ako sa importuju data zo stocard? - do Catima. Alebo exportuju z Stocard.. sorry
Neviem to nikde najst.
Neviem to nikde najst.
Zobrazit příspěvky
Tato sekce Vám umožňuje zobrazit všechny příspěvky tohoto uživatele. Prosím uvědomte si, že můžete vidět příspěvky pouze z oblastí Vám přístupných.
Stran: [1] 2
2
Software / Re:Čím nahradit Stocard?
« kdy: 12. 09. 2024, 09:29:49 »
Ako sa importuju data zo stocard?
Neviem to nikde najst.
Neviem to nikde najst.
3
Sítě / Re:Konfigurace pro MikroTik nefunguje po aktualizaci
« kdy: 12. 10. 2023, 22:34:24 »
Ahoj,
ospravedlnujem sa za neskoru odozvu a nie jednoznacne vyjadrenia.
Najprv k problemu. Z uzivatelskeho hladiska sa to nedarilo replikovat uplne rovnako. DNS neodpovedalo po druhom az piatom dotaze. Mal som pocit, ze sa tocim a neviem najst problem, preto som v strese napisal...
Nam tu pevnu IP od poskytovatela a z nejakeho dovodu som mal pusteneho DHCP klienta /DHCP Client enabled/, co sposobovalo problem - dhcp nedavalo korektny DNS server. Neviem preco v kofiguracii, ktoru som sem dal, to tak nie je.
Nakopli ma rady na sniffer v mikrotiku atd.
Tak vsetkym, ktori dali otazky, dakujem.
ospravedlnujem sa za neskoru odozvu a nie jednoznacne vyjadrenia.
Najprv k problemu. Z uzivatelskeho hladiska sa to nedarilo replikovat uplne rovnako. DNS neodpovedalo po druhom az piatom dotaze. Mal som pocit, ze sa tocim a neviem najst problem, preto som v strese napisal...
Nam tu pevnu IP od poskytovatela a z nejakeho dovodu som mal pusteneho DHCP klienta /DHCP Client enabled/, co sposobovalo problem - dhcp nedavalo korektny DNS server. Neviem preco v kofiguracii, ktoru som sem dal, to tak nie je.
Nakopli ma rady na sniffer v mikrotiku atd.
Tak vsetkym, ktori dali otazky, dakujem.
4
Sítě / Re:Konfigurace pro MikroTik nefunguje po aktualizaci
« kdy: 03. 10. 2023, 22:00:00 »
Konfiguracia je od nuly v 7.11.2 - ta co je uvedena. Tam nechodi. Ked spravim downgrade, tak chodi.
Vsetky dalsie nastavenia este nerobim, kym nechodi zaklad... Ako som napisal, asi potrebujem kontrolu dalsich oci. Ale skusam sniffer a tdpdump kazdej verzii firmware a napisem, ake su rozdiely.
Vyskusam, aj "use-peer-dns=yes" v pppoe.
Vsetky dalsie nastavenia este nerobim, kym nechodi zaklad... Ako som napisal, asi potrebujem kontrolu dalsich oci. Ale skusam sniffer a tdpdump kazdej verzii firmware a napisem, ake su rozdiely.
Vyskusam, aj "use-peer-dns=yes" v pppoe.
5
Sítě / Re:Konfigurace pro MikroTik nefunguje po aktualizaci
« kdy: 03. 10. 2023, 08:44:43 »
Zatial dakujem. Mal som pocit, ze chodim v kruhu... Upgrade cez routerboard rovnako nechodi.
Vyskusam mikrotik sniffer.
Nemam moznost to vyskusat ihned, je to ina lokalita. Ked budem mat viac info, napisem podrobnosti.
Vyskusam mikrotik sniffer.
Nemam moznost to vyskusat ihned, je to ina lokalita. Ked budem mat viac info, napisem podrobnosti.
6
Sítě / Re:Konfigurace pro MikroTik nefunguje po aktualizaci
« kdy: 02. 10. 2023, 15:30:36 »
Tu je cela konfiguracia. Na zaciatku to precita jednu stanku na webe. Pri druhej stranke to nevie preniest data - nerozozna DNS. Pri vytvoreni VPN z klientov sa vsetko rozbehne. Downgrade softu a ide vsetko bez zasahu do konfiguracie.
dik
# sep/29/2023 12:41:50 by RouterOS 7.8
#
# model = RB750Gr3
/interface bridge
add admin-mac=******** auto-mac=no comment=defconf name=bridge
/interface pppoe-client
add add-default-route=yes disabled=no interface=ether1 keepalive-timeout=disabled name=pppoe-out1 use-peer-dns=yes user=******
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip hotspot profile
set [ find default=yes ] html-directory=hotspot
/ip pool
add name=default-dhcp ranges=192.168.10.101-192.168.10.199
/ip dhcp-server
add address-pool=default-dhcp interface=bridge name=defconf
/port
set 0 name=serial0
/interface bridge port
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
/ip neighbor discovery-settings
set discover-interface-list=LAN
/ipv6 settings
set disable-ipv6=yes
/interface detect-internet
set detect-interface-list=all
/interface list member
add comment=defconf interface=bridge list=LAN
add comment=defconf interface=pppoe-out1 list=WAN
add disabled=yes interface=ether1 list=WAN
/ip address
add address=192.168.10.1/24 comment=defconf interface=bridge network=192.168.10.0
/ip dhcp-client
add comment=defconf disabled=yes interface=ether1
/ip dhcp-server network
add address=192.168.10.0/24 comment=defconf dns-server=192.168.10.1 gateway=192.168.10.1
/ip dns
set allow-remote-requests=yes servers=1.1.1.1,8.8.8.8
/ip dns static
add address=192.168.10.1 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment="defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" connection-state=established,related hw-offload=yes
add action=accept chain=forward comment="defconf: accept established,related, untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=invalid
add action=drop chain=forward comment="defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat connection-state=new \
in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat comment="defconf: masquerade" ipsec-policy=out,none out-interface-list=WAN
/ipv6 firewall address-list
add address=::/128 comment="defconf: unspecified address" list=bad_ipv6
add address=::1/128 comment="defconf: lo" list=bad_ipv6
add address=fec0::/10 comment="defconf: site-local" list=bad_ipv6
add address=::ffff:0.0.0.0/96 comment="defconf: ipv4-mapped" list=bad_ipv6
add address=::/96 comment="defconf: ipv4 compat" list=bad_ipv6
add address=100::/64 comment="defconf: discard only " list=bad_ipv6
add address=2001:db8::/32 comment="defconf: documentation" list=bad_ipv6
add address=2001:10::/28 comment="defconf: ORCHID" list=bad_ipv6
add address=3ffe::/16 comment="defconf: 6bone" list=bad_ipv6
/ipv6 firewall filter
add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=invalid
add action=accept chain=input comment="defconf: accept ICMPv6" protocol=icmpv6
add action=accept chain=input comment="defconf: accept UDP traceroute" port=33434-33534 protocol=udp
add action=accept chain=input comment="defconf: accept DHCPv6-Client prefix delegation." dst-port=546 protocol=udp src-address=fe80::/10
add action=accept chain=input comment="defconf: accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=input comment="defconf: accept ipsec AH" protocol=ipsec-ah
add action=accept chain=input comment="defconf: accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=input comment="defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=input comment="defconf: drop everything else not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=invalid
add action=drop chain=forward comment="defconf: drop packets with bad src ipv6" src-address-list=bad_ipv6
add action=drop chain=forward comment="defconf: drop packets with bad dst ipv6" dst-address-list=bad_ipv6
add action=drop chain=forward comment="defconf: rfc4890 drop hop-limit=1" hop-limit=equal:1 protocol=icmpv6
add action=accept chain=forward comment="defconf: accept ICMPv6" protocol=icmpv6
add action=accept chain=forward comment="defconf: accept HIP" protocol=139
add action=accept chain=forward comment="defconf: accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=forward comment="defconf: accept ipsec AH" protocol=ipsec-ah
add action=accept chain=forward comment="defconf: accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=forward comment="defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=forward comment="defconf: drop everything else not coming from LAN" in-interface-list=!LAN
/system clock
set time-zone-name=Europe/Bratislava
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN
[admin@MikroTik] >
dik
# sep/29/2023 12:41:50 by RouterOS 7.8
#
# model = RB750Gr3
/interface bridge
add admin-mac=******** auto-mac=no comment=defconf name=bridge
/interface pppoe-client
add add-default-route=yes disabled=no interface=ether1 keepalive-timeout=disabled name=pppoe-out1 use-peer-dns=yes user=******
/interface list
add comment=defconf name=WAN
add comment=defconf name=LAN
/interface wireless security-profiles
set [ find default=yes ] supplicant-identity=MikroTik
/ip hotspot profile
set [ find default=yes ] html-directory=hotspot
/ip pool
add name=default-dhcp ranges=192.168.10.101-192.168.10.199
/ip dhcp-server
add address-pool=default-dhcp interface=bridge name=defconf
/port
set 0 name=serial0
/interface bridge port
add bridge=bridge comment=defconf interface=ether2
add bridge=bridge comment=defconf interface=ether3
add bridge=bridge comment=defconf interface=ether4
add bridge=bridge comment=defconf interface=ether5
/ip neighbor discovery-settings
set discover-interface-list=LAN
/ipv6 settings
set disable-ipv6=yes
/interface detect-internet
set detect-interface-list=all
/interface list member
add comment=defconf interface=bridge list=LAN
add comment=defconf interface=pppoe-out1 list=WAN
add disabled=yes interface=ether1 list=WAN
/ip address
add address=192.168.10.1/24 comment=defconf interface=bridge network=192.168.10.0
/ip dhcp-client
add comment=defconf disabled=yes interface=ether1
/ip dhcp-server network
add address=192.168.10.0/24 comment=defconf dns-server=192.168.10.1 gateway=192.168.10.1
/ip dns
set allow-remote-requests=yes servers=1.1.1.1,8.8.8.8
/ip dns static
add address=192.168.10.1 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment="defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" connection-state=established,related hw-offload=yes
add action=accept chain=forward comment="defconf: accept established,related, untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=invalid
add action=drop chain=forward comment="defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat connection-state=new \
in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat comment="defconf: masquerade" ipsec-policy=out,none out-interface-list=WAN
/ipv6 firewall address-list
add address=::/128 comment="defconf: unspecified address" list=bad_ipv6
add address=::1/128 comment="defconf: lo" list=bad_ipv6
add address=fec0::/10 comment="defconf: site-local" list=bad_ipv6
add address=::ffff:0.0.0.0/96 comment="defconf: ipv4-mapped" list=bad_ipv6
add address=::/96 comment="defconf: ipv4 compat" list=bad_ipv6
add address=100::/64 comment="defconf: discard only " list=bad_ipv6
add address=2001:db8::/32 comment="defconf: documentation" list=bad_ipv6
add address=2001:10::/28 comment="defconf: ORCHID" list=bad_ipv6
add address=3ffe::/16 comment="defconf: 6bone" list=bad_ipv6
/ipv6 firewall filter
add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=invalid
add action=accept chain=input comment="defconf: accept ICMPv6" protocol=icmpv6
add action=accept chain=input comment="defconf: accept UDP traceroute" port=33434-33534 protocol=udp
add action=accept chain=input comment="defconf: accept DHCPv6-Client prefix delegation." dst-port=546 protocol=udp src-address=fe80::/10
add action=accept chain=input comment="defconf: accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=input comment="defconf: accept ipsec AH" protocol=ipsec-ah
add action=accept chain=input comment="defconf: accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=input comment="defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=input comment="defconf: drop everything else not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=invalid
add action=drop chain=forward comment="defconf: drop packets with bad src ipv6" src-address-list=bad_ipv6
add action=drop chain=forward comment="defconf: drop packets with bad dst ipv6" dst-address-list=bad_ipv6
add action=drop chain=forward comment="defconf: rfc4890 drop hop-limit=1" hop-limit=equal:1 protocol=icmpv6
add action=accept chain=forward comment="defconf: accept ICMPv6" protocol=icmpv6
add action=accept chain=forward comment="defconf: accept HIP" protocol=139
add action=accept chain=forward comment="defconf: accept IKE" dst-port=500,4500 protocol=udp
add action=accept chain=forward comment="defconf: accept ipsec AH" protocol=ipsec-ah
add action=accept chain=forward comment="defconf: accept ipsec ESP" protocol=ipsec-esp
add action=accept chain=forward comment="defconf: accept all that matches ipsec policy" ipsec-policy=in,ipsec
add action=drop chain=forward comment="defconf: drop everything else not coming from LAN" in-interface-list=!LAN
/system clock
set time-zone-name=Europe/Bratislava
/tool mac-server
set allowed-interface-list=LAN
/tool mac-server mac-winbox
set allowed-interface-list=LAN
[admin@MikroTik] >
7
Sítě / Konfigurace pro MikroTik nefunguje po aktualizaci
« kdy: 01. 10. 2023, 23:01:21 »
Zdar,
nevie niekto poradit, co sa zmenilo pri firmware?
Konfiguracia funkcna pri ver.7.8 nefunguje na 7.11.2, model = RB750Gr3.
Zda sa, ze je problem s DNS...
dik za pripadne rady...
imc
nevie niekto poradit, co sa zmenilo pri firmware?
Konfiguracia funkcna pri ver.7.8 nefunguje na 7.11.2, model = RB750Gr3.
Zda sa, ze je problem s DNS...
Kód: [Vybrat]
/ip dns
set allow-remote-requests=yes servers=1.1.1.1, 8.8.8.8
/ip dns static
add address=192.168.10.1 comment=defconf name=router.lan
/ip firewall filter
add action=accept chain=input comment="defconf: accept established,related,untracked" connection-state=established,related,untracked
add action=drop chain=input comment="defconf: drop invalid" connection-state=invalid
add action=accept chain=input comment="defconf: accept ICMP" protocol=icmp
add action=accept chain=input comment="defconf: accept to local loopback (for CAPsMAN)" dst-address=127.0.0.1
add action=drop chain=input comment="defconf: drop all not coming from LAN" in-interface-list=!LAN
add action=accept chain=forward comment="defconf: accept in ipsec policy" ipsec-policy=in,ipsec
add action=accept chain=forward comment="defconf: accept out ipsec policy" ipsec-policy=out,ipsec
add action=fasttrack-connection chain=forward comment="defconf: fasttrack" connection-state=established,related hw-offload=yes
add action=accept chain=forward comment="defconf: accept established,related, untracked" connection-state=established,related,untracked
add action=drop chain=forward comment="defconf: drop invalid" connection-state=invalid
add action=drop chain=forward comment="defconf: drop all from WAN not DSTNATed" connection-nat-state=!dstnat connection-state=new \
in-interface-list=WAN
/ip firewall nat
add action=masquerade chain=srcnat comment="defconf: masquerade" ipsec-policy=out,none out-interface-list=WANdik za pripadne rady...
imc
8
Windows a jiné systémy / Re:Intel NUC 7 - chybí ovladač disku při instalaci Windows 11
« kdy: 12. 06. 2023, 15:40:09 »
Rovnaký problém - včera. Vyriešený tak, že pod Windows stiahnutý Media Creator /tuším sa to tak volá/ vytvoril usb a potom to išlo bez problémov. Priznám sa, že som nekontroloval ISO download.
imc
imc
9
Bazar / Re:Prodám server HP Proliant MicroServer
« kdy: 06. 09. 2022, 11:38:14 »
No pri cene cca 100€ je cena za novy 60 dost.
Cize nieco do 20€... ak by niekto poradil.
Dik.
Cize nieco do 20€... ak by niekto poradil.
Dik.
Zapomněl jsem napsat, že je server prodaný.
Ventilátor by mohl jít najít přímo originál někde na eBay nebo u prodejců HP/HPE náhradních dílů, cena snad nebude likvidační. Nebo najít něco se stejným konektorem, netuším, jestli měl ventilátor tři nebo čtyři piny, ale při zachování pinů by měl fungovat jakýkoliv větrák.
10
Bazar / Re:Prodám server HP Proliant MicroServer
« kdy: 05. 09. 2022, 18:08:00 »
Ahoj.
Prosím, neviete mi poradiť, kde kúpiť ventilátor za rozumnú cenu. Prestal sa točiť a odmietne boot...
Alebo, ako to spraviť, aby akceptoval iný.
Ďakujem
Prosím, neviete mi poradiť, kde kúpiť ventilátor za rozumnú cenu. Prestal sa točiť a odmietne boot...
Alebo, ako to spraviť, aby akceptoval iný.
Ďakujem
11
Distribuce / Re:Distribucia Thinkpad E14
« kdy: 22. 01. 2022, 23:14:08 »
OK. Aspon nejaka skusenost s notebookom na AMD 5700U alebo 5800U.
dik
imc
dik
imc
12
Distribuce / Distribucia Thinkpad E14
« kdy: 22. 01. 2022, 21:41:17 »
Zdravim,
ma niekto skusenost s Thinkpad e14 (AMD) a linuxom z hladiska kompatibility? Podpora vsetkych periferii atd.
Hlavne Fedora vs nieco na *.deb (ubuntu).
Zaujima ma konkretna skusenost, nie vseobecne volba distribucie.
Dik
imc
ma niekto skusenost s Thinkpad e14 (AMD) a linuxom z hladiska kompatibility? Podpora vsetkych periferii atd.
Hlavne Fedora vs nieco na *.deb (ubuntu).
Zaujima ma konkretna skusenost, nie vseobecne volba distribucie.
Dik
imc
13
Sítě / Re:Prepojenie CAT6a kablov
« kdy: 25. 06. 2021, 11:26:13 »Ja by som odporucil spojkovy box. Ktory sa nacvakava ako keystone. A neni potrebny ziadny zbytocny medzi kus. Navyse box je urceny pre vsetky typy kablov od cat5e az po cat7. Da sa dodatocne zaizolovat vulkanizacnou paskou, takze je aj vode odolny Staci si dat hladat do googla spojovacie boxy na cat6a a urcite najde predajcu v okoli, u ktoreho ich viete zakupit.Myslis asi toto........
Aj to je moznost, ale mal som skor na mysli nieco taketo -
Toto chce nastroj.
dastin dastin odporucil beznastrojovu - podobne ja ten konektor, co som pisal predtym.
No a k pajkovaniu - kabel je kruteny. Kazdy par inak. Dovod - prenos pozadovanych stoviek Mhz. Standardne sa meraju presluchy medzi parmi kabla, aj medzi kablami, odrazy... bavime sa o spojke za cca 10€.
Neviem, ci to za to stoji, robit si problemy.
Ked je nieco zle na fyzickej vstve, nemoze to byt lespie vyssie. Mozu nasat chyby a nasledne aj opakovanie prenosu paketu... A tazko sa nasledne hladaju chyby.
Ale, ak ide len o PoE napajanie, tak staci aj pajka.
14
Sítě / Re:Prepojenie CAT6a kablov
« kdy: 24. 06. 2021, 10:12:31 »
Tak pajkovacku by som urcite neskusal. Fyzika(priroda) nepusti. Teda, pokial to ma byt standardny ethernet, okrem napajania. Osobne by som to nechal co najviac standardne - keystone na strane zasuvky aj panelu v racku. A patch kabel. Pripadne, ak sa neda inak, ten konektor alebo spojka, ktora tu bola spominana na instalacny kabel do AWG22 - oba su na rovnakom principe.
Stran: [1] 2
